How To Setup and Programming Endress+Hauser PROSONIC Clamp-On Ultrasonic Flow Meter

27/07/2016 by Leave a Comment

Do you familiar with ENDRESS+HAUSER brand?This time I would like to share about How to setup and programming the PROSONIC Clamp-On Ultrasonic Flow Meter.Also I have attached with video from ENDRESS+HAUSER,method and detail step how to setup the program for PROSONIC Clamp-On Ultrasonic Flow Meter.It very user friendly and easy to setup.

This is basic information about Endress+Hauser Prosonic Clamp-On Ultrasonic Flow Meter :-

The measuring device described in these Operating Instructions is to be used only for measuring the flow rate of liquids in closed pipes.
Examples:
• Acids, alkalis, paints, oils
• Liquid gas
• Ultrapure water with low conductivity, water, wastewater  Read More

Filed Under: Instruments Tagged With: , , , , , , , , , , , , , , , , , ,

How It’s Work : SMC Auto Drain Functional and Operation

26/07/2016 by Leave a Comment

This time I would like to share about Auto Drain operational to discharge automatically water inside compressed air receiver tank.This equipment is very important to remove 80% of water contain in compressed air and to ensure our compressed air is dry and clean.Why we need the clean and dry compressed air in our system?The main reason is to ensure our pneumatic equipment or instrument fully operated and pro long a life span.If water contaminated our compress air system,piping or equipment that operated with compress air will rusty,jammed and clog with dirt.It’s can cause a breakdown and it loss to our operation cost.

Below is example of SMC Auto Drain Operational to remove out water inside receiver tank.We can see a lot of water came out to drainage when auto drain operated.You can image how much water can go through inside to air supply system and can damage our equipment and pipeline.Feel free to watch the video and please share,like or comment if you think it’s benefit. Read More

Filed Under: General Tagged With: , , , , , , , , , , , , , , ,

How to setup Alfa Laval Think Top Auto Valve?

13/08/2013 by Leave a Comment

Alfa Laval Think Top is a control of sanitary valves that commonly used for hygiene or chemical manufactures.Think Top Basic offers a durable watertight design, a proven and inherently safe design and low total cost of ownership.

In my plant,all auto valves are using Alfa Laval Think Top that provide easy installation and configuration.This valve sensing and control head is optimized with fewer options and fewer digital connections. Think Top Basic is available in Digital, AS-Interface and ATEX versions.The ThinkTop Basic sensing and control unit is a uniform modular control head that consists of a proven no-touch, set-and-forget sensor system with light-emitting diodes (LEDs), solenoid valves and valve control sensor board for connection to any PLC (Programming Logic Controller) system.

read more

Filed Under: Instruments Tagged With: , , , , , , ,

Sensor Classification

07/08/2013 by Leave a Comment

Sensor classification schemes range from very simple to the complex. Depending on the classification purpose, different classification criteria may be selected. Here, we offer several practical ways to look at the sensors.

All sensors may be of two kinds: passive and active. A passive sensor does not need any additional energy source and directly generates an electric signal in response to an external stimulus; that is, the input stimulus energy is converted by the sensor into the output signal.

The examples are a thermocouple, a photodiode, and a piezoelectric sensor. Most of passive sensors are direct sensors as we defined them earlier. The active sensors require external power for their operation, which is called an excitation signal. read more

Filed Under: Automation Tagged With: , , , , , ,

Introduction of Servo Motor

01/08/2013 by 1 Comment

In the industrial application for automation technology,Servo motor is the one of common used for high technology equipment that provided more efficiency and precision tune for movement.It’s have a rotary actuator that can make it have a precise control for angular position.

Servo motors have small diameter rotors for low inertia to provide a rapid response. They are fractional to small integral Hp in size and they typically have resolver or encoders to provide very precise speed and position sensing.

They are also almost always Totally Enclosed Non- Ventilated (TENV) enclosures.Below I had listed 3 types of servo motors that commonly used for industrial application. read more

Filed Under: Electric Motor Tagged With: , , , , , ,

Basic of Motor Control

01/08/2012 by 2 Comments

What is definition of motor control?This is familiar question from electrical person around the world.Motor control is common practice for machine application and industry operation.

Basically motor control definition is to STOP and START the electric motor.Technology and innovation of motor control is always developed to parallel with current application needed.

Motor control have a two basic methods.There is MANUAL control and MAGNETIC control.I describe detail about manual and magnetic control circuit diagram and basic operation. read more

Filed Under: Motor Control Tagged With: , , , , , ,

Sensor

19/05/2011 by 2 Comments

This device is very common used in manufacturing industry,office,house hold,school,highway and every placed around us.It very important to sensing and send a signal to control panel for further application.

Basically we can elaborate meaning of sensor in easy understanding are device to detected physical condition such as temperature,pressure,motion,metal and non-metal and many more function.

Sensor application very popular  for industries such as automotive,FPD and semiconductor,machine or metal,ICs and electronic components,food processing and packaging also rubber and plastic.It successful to make production running properly,accurate,smooth and faster. read more

Filed Under: Automation Tagged With: , , , , , , ,
Next Page »